Bucket Elevator Gearbox | Gearboxes

bucket elevator parts, bucket elevator gearbox, bucket elevator belt, bucket elevator chain. DCY conical cylindrical bucket elevator parts includes: DCY160, DCY180, DCY200, DCY224, DCY250, DCY280, DCY315, DCY355, DCY400, DCY450, DCY500, DCY560, DCY630, DCY710, DCY800. The hardened bucket elevator parts mainly includes the parallel shaft series and the vertical shaft series. The parallel shaft Bucket elevator parts is produced according to the national standard (GBl9004—88). The product is optimized and has the international advanced level in the 1980s. It mainly includes ZDY (single). Four series, ZLY (two-stage), ZSY (three-stage) and ZFY (four-stage), vertical shaft Bucket elevator parts is produced according to national standard (JB/T9002-1999), and the input shaft is perpendicular to the output shaft. Directional transmission, which mainly includes three series of DBY, DCY and DFY. bucket elevator parts Feature editing (1) The main parameters such as center distance and nominal transmission ratio are optimized, and the main parts and parts are interchangeable. (2) The bucket elevator gearbox are made of high-quality alloy steel by carburizing and quenching, and the hardness of the tooth surface reaches HRC54-62. (3) Small size, light weight, high precision, large carrying capacity, high efficiency, long life, high reliability, stable transmission and low noise. (4) Generally use oil pool lubrication, natural cooling, when the thermal power can not be met, you can use circulating oil lubrication or fan, cooling coil cooling. Application scope (3) Working environment—40~50°C. If it is lower than 0°C, the lubricating oil should be preheated to above 0°C before starting. The Bucket elevator parts can be used in both forward and reverse directions. (4) It can be widely used in metallurgy, mining, chemical, building materials, lifting, transportation, textile, paper, equipment, plastics, rubber, engineering machinery, energy and other industrial sectors. bucket elevator parts First, single-stage cylindrical bucket elevator parts: The rotating teeth can be made into straight teeth, helical teeth and herringbone teeth. Straight teeth are used for lower speed (ν ≤ 8m / s) lighter load; helical bucket elevator gearbox are used for higher speed transmissions, and herringbone bucket elevator gearbox are used for heavy load transmissions. The housing is usually made of cast iron. Single or small batch production sometimes uses welded construction. Bearings generally use rolling bearings, and use sliding bearings for heavy loads or particularly high speeds. Other types of bucket elevator parts are the same as this Second, two-stage cylindrical bucket elevator parts: 1.Expandable The structure is simple, but the position of the bucket elevator gearbox relative to the bearing is asymmetrical, so the shaft is required to have a large rigidity. The high-speed bucket elevator gearbox is arranged away from the torque input end, so that the torsional deformation of the shaft under the action of the torque and the bending deformation of the shaft under the bending moment can partially cancel each other to slow the uneven distribution of the load along the tooth width. phenomenon. For occasions where the load is relatively stable. The high speed stage is generally made of helical teeth, and the low speed grade can be made into straight teeth. 2. Split type The structure is complicated, but since the bucket elevator gearbox are symmetrically arranged with respect to the bearing, the load is evenly distributed along the tooth width compared with the unfolding type, and the bearing is uniformly loaded. The torque on the dangerous section of the intermediate shaft is only half of the torque transmitted by the shaft. Suitable for variable load applications. High-speed grades generally use helical teeth, and low-speed grades can use straight or herringbone teeth. 3. Coaxial The lateral dimension of the Bucket elevator parts is small, the depth of the two pairs of bucket elevator gearbox immersed in the oil is about the same, but the axial dimension is large and the weight is large, and the intermediate shaft is long and the rigidity is poor, so that the load distribution along the tooth width is uneven. The bearing capacity of high-speed shaft is difficult to make full use of 4. Coaxial split type Each pair of meshing bucket elevator gearbox transmits only half of the total load. The input and output shafts are only subjected to torque. The intermediate shaft is only half of the total load, so the journal size can be reduced compared to other bucket elevator parts that transmit the same power. bucket elevator parts. For more details please email us at